Author Topic: CZ P10 C Optics Ready magazine pinches my little finger when firing  (Read 510 times)

Offline Dbwbroker

  • Newbie
  • *
  • Posts: 3
Hello everyone I have a CZ P10 C that’s optics ready that I really like, having said that I would like to know if anybody else has any experience with their small finger on the trigger hand being pinched between the magazine and the grip?
i Tried to put a small piece of tape in the gap however it seem to stop the slide from going all the way back when the clip was empty. I’m sure hoping to find some type of remedy. The clips that I have are CZ Manufactured. I also tried one with a plus 2 addition same issue.
Any help with this issue would be appreciated. Thank you !
https://share.icloud.com/photos/0xslgk3poBuVVxIgrGYl7sqcw
« Last Edit: May 19, 2021, 07:34:14 PM by Dbwbroker »

Offline frgood

  • Sr. Member
  • ****
  • Posts: 424
From the picture it is clear either the magazine is not seated correctly or the extension is installed incorrectly.  If the slide is not locking back then seating is suspect. However improper installation of the extension may be causing the magazine to not seat correctly.


I might tr removing the extension and simply confirming the magazine seating position in the frame to confirm the frame and magazine case are within spec. I would then check the magazine tube and the parts for burrs or any other manufacturing extra bits that might cause some sort of hangup. Also check the frame for any burrs that could hinder proper magazine seating and sandpaper accordingly.


Let us know what that inspection uncovers.

Offline Dbwbroker

  • Newbie
  • *
  • Posts: 3
Thank you very much for your input. I did inspect the magazine seems to be properly installed. I also have my OEM Magazine that doesn’t seem to be any better I will include some pictures if you’d be so kind to let me know what you think. I did some checking around the web and it seems that other people are complaining about finger pinch with other compact model pistols. I also saw where some people were putting a number 17 O-ring around the mag which prevents the pinch, so I purchased some and they do seem to work. However , I think that the clearances should be much tighter from the manufacturer. 

https://share.icloud.com/photos/0gdcmedjWhk-HY5fatq3lahZQ
https://share.icloud.com/photos/0CM9Q-_LSABKGRHTcMlh87w7A
https://share.icloud.com/photos/01tvheB9Z4k6rY8clgR44feMw
https://share.icloud.com/photos/0E33OBKhf-1UNpKgk_F4ADwMQ
« Last Edit: May 21, 2021, 01:04:13 PM by Dbwbroker »

Offline frgood

  • Sr. Member
  • ****
  • Posts: 424
Perhaps getting a picture of the top of the frame?  It sounds like it is worth a call to CZ support as there may be an issue with the frame, albeit minor, if all the magazines are not seating well.


Offline Dbwbroker

  • Newbie
  • *
  • Posts: 3
Here is a picture of the inside of the frame. Thank you for your time and helping me with this problem.
Just got off the phone with CZ USA. Sorry to say, not much sympathy from them, I was very polite and explained the issue ...The  service person (Jacob)told me if it were out of tolerance it would not cycle. Said “dont hold your pinky over the crack”.
Have to you say this is my first service experience with CZ. Found it to be somewhat disappointing.

https://share.icloud.com/photos/0AG98PLK56HmnbaACbpjSUweA
« Last Edit: May 21, 2021, 04:01:48 PM by Dbwbroker »